OHM 很自豪地向大家介绍这款功能齐全的音箱系统控制器Cleo Mk2 2-6,该控制器内置DSP处理器采用48kHz采样和48dB/oct滤波器,2通道输入6通道输出可以灵活组合的多种分频模式。能够储存60组使用者自编的程式。为OHM音箱预置系统参数,特有的安全保护锁定模式和隐藏程式设置。前面板设有独立输出哑声按键及电平指示灯,还能通过PC电脑进行实时监控。
Imputs
Two
Input impedance
10k Ohm electronically balanced
Maximum input level
+20dBu
Input Gain
±15db variable in 0.1dB steps
CMRR
Better than 50dB (30Hz-20kHz)
Imput Connector
XLR-3F or equivalent
Imput sample rate
44.1, 48, 88.2, 96kHz
Output impedance
<50 Ohms electronically balanced
Maximum ouput level
±20dB into 600 Ohms or greater
Gain
±21dB, variable in 0.1dB steps
Output connector
XLR-3F or equivalent transformer balanding option
Crossover filters - slopes
6, 12, 18, 24, or 48dB per octave (filter type dependant)
Crossover filters - type
Bessel, Butterworth or Linkwitz - Riley
Delays available on /inputs A, B and Outputs
1, 2, 3, 4, 5, 6
Delay step
11 microseconds minimum
Max Delay time
2.6 seconds
EQ Gain
±15db variable in 0.2dB steps
EQ type
Parametric, bell or shelving on any filter. Nine filters assigned to Dynamic EQ
Q (bandwidth)
0.05 to 3 octaves, variable in 0.005 steps
EQ Frequency
15Hz to 20kHz
Dynamic slope
2:1 to 20:1 (dynamic EQ`s only)
General performance with filters
Out
Frequency response
15Hz-20kHz,± 0.25kB 15H\ -40kHz, ±3dB
Dynamic range
>112dB uniweighted 22Hz to 22kHz, Output >117dN on AES/EBU input
Chanel separation
>80dB, 30Hz to 20kHz
Distortion (THD)
<0.005%, 20Hz-20kHz@ ±10dBu Output
Input metering
-20dB, -12dB, -6dB, -3dB, Clip relative to Clip point (+20dBu)
Output meter indication
SIG (-40dB), -20dB, -12dB, -6dB, -3dB, 0dB, Over (+6dB) relative to limiter treshold setting
Mains power
110V - 240V AC. 50/60Hz, 30VA
Dimensions (mm)
44 x 418 x 223 (H x W x D)
Weight (kgs)
3.6
CRED 是专门为音响系统工程师开发的必要和综合性的数字化工具。这个已经升级的音箱处理器版本能够为今天的音响工程技术人员提供显著的帮助。通过对用户反馈信息的分析,OHM开发了这个全面升级的CRED音箱控制器,它为音响设计师和工程技术人员配备了完整的系统控制参数,大小仅需占用1U的机柜空间。用户可以控制两个信号输入端和六个信号输出端,调节延时参数,增益参数以及倍频程均衡参数。CRED由始至终履行职责,全面协助管理、监控、保护以及完善系统。 CRED 预装了OHM所有的音箱/功放系统资料和厂家推荐的分频点,使操作更加简化直观。
Two [Cred 2-4 & Cred 2-6]
>10k Ohm electronically balanced
Outputs
Four [Cred 2-4] or six [Cred 2-6]
Outputs impedance
<100 Ohm, ground balanced
+20dBu into 600 Ohm load
Sample rate
96kHz
10Hz to 40kHz, 1.0dB (filters disabled)10Hz to 20kHz, 0.25dB (filters disabled)
THD
<0.01%, (+10dBu, 20Hz to 20kHz, 30kHz bandwidth)
>111dB (A weighted, 22kHz bandwidth)>108dB (A weighted, 22kHz bandwidth)
Serial comms data
38.4kbaud, format: 8 data, 1 stop, no parity
Audio inputs
3 pin female XLR
3 pin male XLR
Serial comms
9 pin female `D type`
Network comms
Future option
+20dB to -80dB and mute, 0.2dB steps
Output ch. source
Input A, Input B and SUM
HP filter frequency
Off, 10Hz to 25,4kHz, 1/36 octave steps
LP filter frequency
10Hz to 25,4kHz, and off 1/36 octave steps
HP / LP filter type
12, 18 & 24dB / octave Bessel and Butterworth, 12 24 and 48dB / octave Linkwitz Riley and 4th or 8th order hardman
Maximum delay
Input 400ms, output 80ms
Limiter
High performance limiter, adjustable treshold in 0.2dB steps, automatic time constans
15Hz to 25kHz, 1/36 octave steps
+15db to -15dB, 0.2dB steps
EQ width
5.0 to 0.1 octaves bandwidth, 1/36 octave steps
Mains
3 pin IEC
uniwersal switch mode PSU, 85V to 250V AC, 50/60Hz Audio
Consuption
<25 Watts
44 x 482 x 254 (H x W x D)
2.1